Difference between revisions of "Mediaclient"
Jump to navigation
Jump to search
| (4 intermediate revisions by the same user not shown) | |||
| Line 6: | Line 6: | ||
: -m DVBS or DVBS2 | : -m DVBS or DVBS2 | ||
| − | : -f Frequency in | + | : -f Frequency in KHz |
: -M modulation 8PSK or QPSK | : -M modulation 8PSK or QPSK | ||
: -S Symbol Rate | : -S Symbol Rate | ||
: -E FEC | : -E FEC | ||
: -V Voltage (V or H) | : -V Voltage (V or H) | ||
| + | |||
| + | Additional for Multistream (just skip it if not needed): | ||
| + | |||
| + | : --plsmode=[GOLD, COMMON, ROOT] | ||
| + | : --plscode=[plscode] | ||
| + | : --isi=[stream id] | ||
: please note that those parameters very likely don't match the setup of your dish and you might not get a [LOCKED]. This is only an example what the commandline string looks like. Adjust it to parameters which are suitable for your setup. Eg. get the DVB-S/S2 parameters from https://lyngsat.com | : please note that those parameters very likely don't match the setup of your dish and you might not get a [LOCKED]. This is only an example what the commandline string looks like. Adjust it to parameters which are suitable for your setup. Eg. get the DVB-S/S2 parameters from https://lyngsat.com | ||
| + | |||
| + | Example for Multistream: | ||
| + | |||
| + | Eutelsat 5 West B at 5.0°W | ||
| + | |||
| + | <pre> | ||
| + | /opt/bin/mediaclient -m DVBS2 -f 12536000 -M 8PSK -S 35300000 -E 2/3 -V H --plsmode=GOLD --plscode=131070 --isi=9 | ||
| + | </pre> | ||
=== DVB-C Tuning === | === DVB-C Tuning === | ||
| Line 35: | Line 49: | ||
=== Reading Signal statistics === | === Reading Signal statistics === | ||
| − | /opt/bin/mediaclient --readsignal=0 -d /dev/dvb/adapter0/frontend0 | + | /opt/bin/mediaclient --readsignal=0 --band=universal -d /dev/dvb/adapter0/frontend0 |
: --readsignal=N N.. 0=infinite; N.. times | : --readsignal=N N.. 0=infinite; N.. times | ||
: -d device name | : -d device name | ||
| + | : --band=universal .. for DVB-S/S2 Universal LNB (to recalculate the current frequency), for C-Band use cband (for DVB-T or DVB-C skip this command | ||
=== Scanning transponder === | === Scanning transponder === | ||
/opt/bin/mediaclient --tsscan /dev/dvb/adapter0/dvr0 | /opt/bin/mediaclient --tsscan /dev/dvb/adapter0/dvr0 | ||
Latest revision as of 21:23, 21 August 2024
Contents
Mediaclient
DVB-S/S2/S2X Tuning
/opt/bin/mediaclient -m DVBS -f 12400000 -M 8PSK -S 27500000 -E 2/3 -V V
- -m DVBS or DVBS2
- -f Frequency in KHz
- -M modulation 8PSK or QPSK
- -S Symbol Rate
- -E FEC
- -V Voltage (V or H)
Additional for Multistream (just skip it if not needed):
- --plsmode=[GOLD, COMMON, ROOT]
- --plscode=[plscode]
- --isi=[stream id]
- please note that those parameters very likely don't match the setup of your dish and you might not get a [LOCKED]. This is only an example what the commandline string looks like. Adjust it to parameters which are suitable for your setup. Eg. get the DVB-S/S2 parameters from https://lyngsat.com
Example for Multistream:
Eutelsat 5 West B at 5.0°W
/opt/bin/mediaclient -m DVBS2 -f 12536000 -M 8PSK -S 35300000 -E 2/3 -V H --plsmode=GOLD --plscode=131070 --isi=9
DVB-C Tuning
/opt/bin/mediaclient -m DVBC -f 450000000 -S 6900000 -M Q256
- -f Frequency in Hz
- -S Symbol Rate
- -M Modulation Q256 or Q128 or Q64
DVB-T/T2 Tuning
/opt/bin/mediaclient -m DVBT -f 450000000 -b 8
- DVBT or DVBT2
- -f Frequency in Hz
- -b bandwidth in Mhz
If the device supports DVB-T2 the driver will also lock on DVB-T2 transponder (regardless if DVBT only is set)
Reading Signal statistics
/opt/bin/mediaclient --readsignal=0 --band=universal -d /dev/dvb/adapter0/frontend0
- --readsignal=N N.. 0=infinite; N.. times
- -d device name
- --band=universal .. for DVB-S/S2 Universal LNB (to recalculate the current frequency), for C-Band use cband (for DVB-T or DVB-C skip this command
Scanning transponder
/opt/bin/mediaclient --tsscan /dev/dvb/adapter0/dvr0
